Right here below yow will discover more quality advice when it comes to Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a new one is additionally a reasonably challenging project. If the old bathtub is easily accessible, the task can relocate rapidly; if you have to open a wall surface to eliminate the old tub and place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub and also set in the new one. Ensure you have actually qualified yourself for the task and fit trying it. Rather than working with a specialist to take control of a halfway-completed project, it is better to take into consideration employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you install a brand-new bathtub in your washroom if you have currently purchased a new tub and also don't require to change the plan of your previous supply of water pipelines.
Your tools as well as material checklist need to make up the following:
Getting ready for the Installation
To start with, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent strain on the bathtub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final position.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed position. The wooden boards are handy in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bathtub till the spirit level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the tub and additionally check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait until the tub has been made use of at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers are in area between the faucet and also the sink. Secure the faucet in position with the producer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind should be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to problems with wetness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes as well as cartridges, as well as are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on a different website. Do you know about someone else who is curious about the niche? Feel free to share it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Or Book Technician Here